| Product
Issues include:
How flexible is it?
The flexibility of the molding pattern depends upon several
factors. Pattern size, shape, material type and application all determine
the flexibility limits of a given pattern. The smaller the molding the
more flexible it will be. A ½" x ½" Cove mold will be very
flexible and will accommodate most any curvature while a 2-½" x 2-½"
Brick Mold will be very stiff and will usually require pre-forming at the
factory.
Moldings that are thinner in one dimension than the other, like a ½"
x 3-½" Base Molding, will bend easily in the direction of the lesser
dimension. This is why Base Moldings usually require no pre-curving while
the same size Casing, bent on edge, must be pre-curved to fit the opening.
Some applications consisting of a single large radius may be
accommodated using a straight flexible length without pre-curving. Smaller
curves, irregular shapes and compound radius applications will usually
require pre-curving at the factory.
Ordering
Typical Application Types
True Radius Casing: Half
circle, quarter circle, full circle and arched casing must be pre-curved in
most cases. Order true radius casing by specifying the radius, specie and
the length of material required. (see below for specific
requirements in definition of terms)
Straight Applications: When
ordering straight applications such as base, flat or jamb stock, order the
length needed, specie and in cases of a small radius state if it needs to
be bent on the face or back. (see below for specific requirements in
definition of terms)
Definition of Terms
True Radius Casing
Half circle, quarter circle, full circle and arch casing must be
pre-curved in most cases. Order true radius casing by specifying the
radius, specie and the length of material required.
Corner Mold patterns
are typically small and bend easily without need for pre-curving. Larger
patterns may require pre-curving at the factory. When ordering pre-curved
patterns, indicate in which direction the Corner Mold will need to be
bent. Include the molding pattern, specie and length required when
ordering.
Cove Mold is similar
to ordering Corner Mold. When ordering pre-curved material indicate which
side of the curve the Cove will face.
Plant On patterns are
typically small and therefore bend easily without any need for
pre-curving. Large patterns however may require pre-curving at the factory
if they are to be bent on edge. If the pattern does require pre-curving,
you will need to specify which side of the pattern faces which side of the
curve. Compound radius curves may require a template. Include the molding
pattern, specie and length required when ordering.
Panel Mold is similar
to Plant On patterns. Orders for Panel Mold that require pre-curving must
indicate which side of the curve the rabbet (notch) faces.
Stucco Mold is similar
to Plant On patterns. Orders for Stucco Mold that require pre-curving must
indicate which side of the curve the stucco key faces.
Base is typically bent
on the its back rather than it's edge and therefore requires no
pre-curving unless the radius is extremely tight (less than 9"). To
order specify the molding pattern, specie and length required.
Definitions:
- Diameter - The width of a circle at the
center.
- Radius - The measurement from the exact center
to the outside or circumference. Half the diameter.
- Width-The measurement of the area to be
trimmed at its widest point.
- Rise-The measurement from the imaginary line
which is the width where the curve begins, to the top of the curve.
What
if your application is Custom?
Orders for custom applications (orders that do not fit into the category
of straight or preformed as show on the catalog pages) should be submitted
via email for review and pricing.
Be sure to include the molding profile, specie and a detailed description
of the applicaiton.
What's it
made out of?
 carries only
Flextrim Products. Because of their long term standing in
the business and reputation for unsurpassed product quality, we feel comfortable in
knowing our customers will have complete satisfaction.
ZzzzFLEX® Flexible molding
All flexible molding sold by
is made of ZzzzFLEX by Flex Trim(R). ZzzzFlex is the state of the art in flexible molding technology. No
other flexible molding is stronger, more durable or stains up better
than ZzzzFLEX. ZzzzFLEX is an elastomer composite developed for the most
demanding applications. Use ZzzzFLEX for small intricate patterns and
tight curvatures or when only the best will do.
Renaissance®
The accessories offered by
are made of the highest quality polymers manufactured by Flex Trim.
These items from Flex
Trim's Renaissance Collection ®, are paint
able, stain able and very durable. Use Renaissance for all your interior
and exterior accents.
Stainability
Staining Flex Trim products is similar to staining wood. Most
stains work well however, use of thicker heavily pigmented stains is
recommended. Thinner stains may require multiple coats. Staining flexible
moldings prior to installation is not recommended as the stain may crack
when the molding is flexed during installation.
- Before Painting or staining be sure the material is clean and free
of dirt and oils. Clean with paint thinner or soap and water if
needed.
- Mask off any adjacent non-stain areas.
- Apply the stain with a brush covering the entire surface of the
material, especially in any deep grooves or crevices that may exist.
- Wipe off majority of excess stain with a soft, clean, dry rag.
- Wipe off remaining excess stain with a brush.
- Clear coat with lacquer, polyurethane or varnish using spray
equipment. Applying clear coats with a brush may remove stain.
Paintability
Painting Flex Trim products is easier than painting wood.
ZzzzFLEX molding require no priming or sanding prior to painting. Painting
flexible moldings prior to installation is not recommended as the paint
may crack when the molding is flexed.
- Before Painting or staining be sure the material is clean and free
of dirt and oils. Clean with paint thinner or soap and water if
needed.
- Fill and sand all nail or screw holes.
- Mask off any adjacent areas. Priming prior to painting will improve
finish luster but is not required.
- Apply the paint with a brush or spray equipment covering the entire
surface of the material, especially in any deep grooves or crevices
that may exist.
- Add additional coats as desired.
Cutting
ZzzzFLEX may be cut using the same tools and equipment and in the
same manner as wood. Before cutting to length, make sure the material is
held firmly against the saw table or fence. Place a backing (such as a
piece of wood) directly behind the cutting area. Always cut the material a
little long and shave to exact length.
When ripping ZzzzFLEX on a table saw make sure the material will stay
firmly against the fence during the cut and that it can be fed easily and
continuously.
Fastening
Pre-determine placement and
layout prior to fastening molding into place. Use of construction adhesive
in addition to nails or screws is recommended due to the flexible nature
of the material. Failure to adequately adhere flexible molding may result
in sags between fastening points. All standard methods of fastening work
well with ZzzzFLEX flexible moldings.
Machining
It is possible to machine shape ZzzzFLEX flexible moldings. When
machining flexible molding the material must be securely held to the
fence, guide or holder especially at the beginning of the cut, when the
material first enters the machine cutter. Always make several small
incremental cuts rather than one large one.
Machining of stain grade
material will remove the grain texture from the cut surface.
Usage Outside
Flex Trim products are
not effected by salt, moisture, heat or extreme cold. Many builders and
home owners have selected to replace even straight exterior moldings with
Flex Trim products because of their durability in the harshest
environments.
General Issues include:
Payment
We accept VISA and Master Card.
Sales Tax
We are required to charge state sales tax on all items shipped to destinations in California. Any applicable tax will be calculated automatically upon completion of the online order form.
Shipping Charges
We ship all items via UPS. Shipping charges are listed with
the item’s price. Large orders are shipped through a reliable freight
carrier. Shipping charges for freight items are determined by the weight
of the product and its destination. For expedited shipping, shipments
via freight carrier, or shipments outside the continental United States,
please contact our Customer Service Specialists.
All Items marked are shipped directly from the manufacturer in the
time frame indicated. All items will be charged to your credit
card when we receive your order so that the manufacturer can begin processing
your order.
Shipping Time
Most orders ship within 2 weeks of ordering. Time in transit
depends upon the several factors but is usually 3 days or less.
Catalog
We offer an Adobe Acrobat® version of our catalog
with full size renderings of the profiles we
offer. You can download the catalog and print it using the free Acrobat
Reader® offered by Adobe®
. Use our catalog to match the molding profiles offered to your existing
wood moldings.
Credit
Card Security
Your personal information Is Secure
ITRIM uses the industry standard security protocol Secure Sockets Layer (SSL)
to encode sensitive information like your credit card number that passes
between you and ITRIM. We employ the latest encryption technology in
all areas of the site which require you to provide your personal or
account information. This means that the credit card information you send
is encrypted by your computer, and then decrypted again on our side,
preventing others from accessing your private information in between. So,
when using an SSL capable browser, shopping on ITRIM's web site is
perfectly safe.
Customer Service &
Return Issues include:
Confirmation of Order
Order confirmations will be e-mailed to the address entered on the
order completion page.
Complaints or Concerns
Please e-mail us.
Customer Service Hours
E-mail 24 hours a day 7 days a week. We will reply as soon as
we are able to answer your questions or concerns.
Return of Undamaged Merchandise
We accept returns for "in-stock" items within 30 days of purchase when accompanied by a valid RMA issued by us. The customer is responsible for return shipping. Refunds are issued only for purchased parts. Sorry, but custom ordered items may not be cancelled or returned.
Return of Damaged Merchandise
Please notify us immediately upon receipt of damaged goods for issuance of a return authorization (RMA). We will replace any material that is received by you in damaged condition. We may ask that such material be returned. Return of defective material also requires authorization. Call us for the RMA. We will replace or refund at our discretion.
|
